Current Category : The Fun Kart III - Go to Category Index | Search.

From this page you can securely order parts for the Funk Kart III. You may click here for comprehensive information on the Fun Kart III or click here to go to the plans ordering page.

Instructions: Scroll down the list of parts and find the item or items that you want. For each part enter the quantity that you want and click on the "buy" button displayed for that item. You will then be taken to your current purchase list, and that item should have been added. If you need to order more click back button on your browser and and do the same for each item. However, if at this stage that is all you want to buy click on 'check out'. You will then be asked to fill out your information on a secure server.

All Prices are in Australian Dollars. ( USA residents will only pay approx 75% of list prices quoted due to exchange rates. ) Note: Our Australian dollar is only worth around 75 cents to the US dollar, that means USA residents will only pay around half the price shown here in Australian dollars.

Your Computer: If this page is not working as you think it should please make sure your internet browser has javascript enabled. Our javascript is harmless and enabling javascript can be done for just the time you are at our site if you wish. But generally it is enabled by default. If your not sure how to enbable it please try (in Internet Explorer) going to Tools > Options then the Security Tab where you can set it back to 'Default' or enabling 'Active Scripting'.

	FT01		QTY:
	Chassis Frame, fully welded with holes drilled, mount brackets and axle beam welded on

	FLPN-1		QTY:
	Floor Pan, 2mm sheet, 830mm x 550mm (can only be ordered if ordering FT01 chassis)

	FT02-DUP1		QTY:
	Chassis Frame Pack, pre-cut & drilled ready for welding (no front axle beam) (not needed if ordering FT01 chassis)

	FT03		QTY:
	Front Axle Beam, fully welded with holes drilled

	FT04		QTY:
	Steering Support, fully welded with holes drilled

	FT05		QTY:
	Lower Steering Bracket, drilled

	FT06		QTY:
	Top Steering Bracket, fully welded & drilled

	FT07		QTY:
	4 Steering Bushes for top & lower Steering brackets (acetal)

	FT08-DUP1		QTY:
	Steering Shaft, drilled with Steering Boss welded on

	SB01-DUP2		QTY:
	Steering Boss only (not required if ordering Steering Shaft)

	FT09		QTY:
	Bellcrank, welded & drilled. Comes with 6mm Rollpin

	FT10-DUP1		QTY:
	Lock Collars, drilled & tapped with grub screw

	FT11-DUP1		QTY:
	Tie Rods, welded with lock nuts

	BLIOD		QTY:
	Tie Rod Ends, includes nyloc nuts

	FT12-DUP1		QTY:
	Stub Axles, fully welded with uprights, steering arms, nuts, washers, & split pins

	BSH12-4-DUP1		QTY:
	4 Stub Axle Bushes (acetal)

	STB12-2		QTY:
	2 Stub Axle bolts, 12mm. Includes washers & nyloc nuts

	FT13		QTY:
	Steering Kit, includes above parts: FT04, FT05, FT06, FT07, FT08, FT09, FT10, FT11, FT12, BLIOD, BSH12-4, STB12-2 (Discounted Price)

	FWH-01		QTY:
	Front Wheel Hubs (steel) 5 stud H-T pattern. Includes studs, nuts, bearings, seals & dust caps

	STW-01-DUP3		QTY:
	Steering Wheel, 3-Spoke polymoulded 11" Æ (Black)

	FT14-DUP1		QTY:
	Master Cylinder mount bracket, fully welded & drilled

	MSC-01-DUP5		QTY:
	Master Cylinder 5/8" girling type

	FT15		QTY:
	Master Cylinder Pushrod & Clevis Joint

	FT16-DUP1		QTY:
	Brake Hose, stainless braided with banjo fittings each end

	BB01		QTY:
	Banjo bolt with 2 x crush washers. (2 req'd)

	FT17-DUP1		QTY:
	Brake Kit: includes Master Cylinder, brake hose & caliper. Parts:MSC-01, FT16 & CAL-01

	FT18		QTY:
	Brake Caliper mount bracket, fully welded & drilled

	FT19		QTY:
	Pedals, fully welded & drilled

	FT20-DUP1		QTY:
	Throttle Cable, to suit 6.0 Vanguard motor

	FT21		QTY:
	Rear Axle, 1000mm long, 1 ¼"Æ complete with keyways & wheel hubs fitted

	RWH-01		QTY:
	Rear Wheel Hubs only, 1 ¼" bore 5 stud with studs & nuts

	MHU-01-DUP2		QTY:
	Drive Hub for 82 tooth 3/8" Sprocket, keyed 1 ¼" bore, 4 holes on 4" PCD (2 required per vehicle)

	SPR-01		QTY:
	Rear Drive Sprocket 82 tooth, 35-1, 3/8" pitch steel (suits mount hub: MHU-01)

	CH-351-100-DUP1		QTY:
	35-1, 3/8" Pitch chain 100 links & connector link

	DBR-02-DUP3		QTY:
	Disc Rotor 240mm Æ , 5mm thick steel slotted, (suits mount hub: MHU-01)

	FT22-DUP1		QTY:
	Key steel 10x10mm: 1x 50mm long : 1x 173mm long

See our Conditions of Sale.

[1] 2 Next Page

Secure ecommerce shopping cart software
and credit card processing provided by ezimerchant